| Title |
Author |
Time |
|
Re: Broken Rudder Head
- response to Broken Rudder Head
|
|
Ross
|
5:42am 11.07.09
|
|
What size shaft? I have one not being used that looks like that. The bolt should take all of the st
|
|
Re: Flexing Strut
- response to Flexing Strut
|
|
HunterDon31
|
5:40am 11.07.09
|
|
Thanks Alan Looks like you did a great job on the strut. If i can remove mine with out to much trou
|
|
Re: Where did summer go
- response to Where did summer go
|
|
Tim R.
|
5:27am 11.07.09
|
|
Heading out for an overnighter at the Goslings today. A great local place to spend the night. Nic
|
|
RE: Well, can't say you didn't warn me,,,
- response to Well, can't say you didn't warn me,,,
|
|
Roger LeBlanc
|
5:00am 11.07.09
|
|
Thank you, Rich. After I posted the question, I contacted Hunter, and they sent me the drawings. I
|
|
Re: Comparison charts between Ice box conversion kits
- response to Comparison charts between Ice box conversion kits
|
|
zds
|
4:48am 11.07.09
|
|
Have you tested your box with ice yet? I found my stock icebox (86 model) to be very efficient.
|
|
Re: Chart Plotter Question / Assistance
- response to Chart Plotter Question / Assistance
|
|
agaliha
|
4:35am 11.07.09
|
|
I have a "little" Raymarine 435 mounted in the binnacle. It is linked to the autopilot,
|
Below Deck
- response to best autopilot for an 1985 H40
|
|
seadaddler
|
4:29am 11.07.09
|
|
I really would love to see some photo's of below deck installations,how the below deck is hooked up
|
|
Hull speed and power
- response to 216 power and lights
|
|
Bill Roosa
|
4:21am 11.07.09
|
|
My calculations for flat water hull speed yields 5.5 knot
|
|
How but not where
- response to wiring bow running light
|
|
Bill Roosa
|
3:58am 11.07.09
|
|
I can tell you that the light should have its own power a
|
|
basics
- response to winterization
|
|
Bill Roosa
|
3:48am 11.07.09
|
|
Don't know where a broom crutch could be purchased so can
|
|
Re: 1986 40' hunter. halyard diameter?
- response to 1986 40' hunter. halyard diameter?
|
|
waternwaves
|
11:17pm 11.06.09
|
|
the PO replaced the oversize hunter lines on mine with the same size, as they claimed they were ea
|
|
RE: mast head bulb type
- response to mast head bulb type
|
|
waternwaves
|
11:10pm 11.06.09
|
|
yeah..... bring the digital camera up for: mounting screw sizes, masthead light, bulb, sheaves, r
|
|
Re: best autopilot for an 1985 H40
- response to best autopilot for an 1985 H40
|
|
waternwaves
|
11:02pm 11.06.09
|
|
no, I meant 3 different drive motor connections in H40's lazarette that I have photo's so far so
|
|
Reefer
- response to Fridg Compressor Want Start
|
|
Thread
|
9:53pm 11.06.09
|
|
FWIW, I prefer to dig into a system problem, find the solution and fix it myself. Most system maker
|
|
AP
- response to best autopilot for an 1985 H40
|
|
Thread
|
9:39pm 11.06.09
|
|
Hmm. I'm now even more confused than before. I've not bothered with measuring the power consump
|
|
RE: Flexing Strut
- response to Flexing Strut
|
|
Allan12210
|
9:32pm 11.06.09
|
|
Don, My strut was out of alignment and had to be removed and repositioned so the shaft would run
|
|
RE: mast head bulb type
- response to mast head bulb type
|
|
Brock Halbeisen
|
9:25pm 11.06.09
|
|
understood. one less trip up the mast. get the whole info for the entire mast head light next time
|
|
RE: A question about crossing back from Bimini
- response to A question about crossing back from Bimini
|
|
dserrell
|
8:57pm 11.06.09
|
|
Joe, Thank you for your posting! This past June we took our 89' Compac 19/3, a small salboat, out
|
|
Re: Flexing Strut
- response to Flexing Strut
|
|
Steve Dion
|
8:48pm 11.06.09
|
|
Don: You best bet for the prop is a prop puller. The heat is fine, but there is no guarantee that
|
|
Re: Comparison charts between Ice box conversion kits
- response to Comparison charts between Ice box conversion kits
|
|
waternwaves
|
8:40pm 11.06.09
|
|
Cold plate is the way to go for our size boats. also......a custum made wire shelf with end stan
|
